 |
 |
Congratulations on buying the best in the
off-road lights, the Vision X Off-Road
HID-8500 Series.
All electronics are internal so there is no need to mount
external ballasts. Each
light has a simple 2 wire hook up. Red...
Go |
 |
 |
Congratulations on buying the best in the
off-road lights, the Vision X Off-Road HID-5700 Series.
All electronics are internal so there is no need to mount
external ballasts. Each light has a simple 2 wire hook up.
Red...
Go |
 |
 |
Congratulations on buying the best in the
off-road lights, the Vision X Off-Road HID-6500 Series.
All electronics are internal so there is no need to mount
external ballasts. Each light has a simple 2 wire hook up.
Red...
Go |
 |
 |
Remove the factory bulbs from headlight housing by twisting
¼ turn and pulling outward, unplug bulb from wire harness
and store for possible future use. Install new Vision “X”
HID bulb being careful not to touch the glass part of the
bulb, if you
Go |
 |
 |
Installing 2007 Rhino HID: Remove factory bulb
by twisting stock bulb to the left ¼ turn while pushing
inwards. Disconnect from stock wiring harness
Go |
 |
 |
One thing that really annoyed me with my truck since the day
I got it, was the fact that I had little control of the
lighting system. GM decided that they should control when to
turn on the headlights and designed their AHS (auto headlamp
system).
Go |
 |
 |
This document shows you how to
slow the flash of a turn signal due to a higher impedance
bulb. Due to significantly less amperage draw from our 360
bulbs, the factory flashing unit becomes more efficient,
increasing flashes per minute. A simple resistor paralleled
into the turn signal circuit increases resistance on the
circuit allowing factory flashing unit to operate at factory
speed
Go |
 |
 |
VISION-X UNIVERSAL RELAY HARNESS THIS HARNESS MUST BE
USED IN EVERY INSTALL TO ENSURE PROPER CURRENT FOR HID TO
START.
Go |
 |
 |
Open front hood, remove outer bulbs from stock head light
fixture(see photo). Install Vision X HID bulbs were stock
ones were (see image). Mount Starter Ballast on outer frame
horn of Prowler (see image) Make sure the length is OK from
ballast to bulb and not to short. You can use Self Tapping
screws, please add silicone to screw, it helps prevent the
screw from backing out under vibrations. Still check
occasionally.
Pic 1,
Pic 2,
Pic 3,
Pic 4,
Pic 5,
Pic 6
Go |
 |
 |
Polaris Ranger installation instructions for HID retrofit
upgrade kit. Please note: This kit requires the use of
solder less connectors to factory loom “will not” plug into
factory harness. Remove factory Polaris bulbs, and replace
with Vision X HID bulbs (put a dab of silicone on outer lip
of bulb after installed). Mount each Vision X ballast to the
left or right of the stock upper shock mount. Please note:
You will be required to drill an
Go |
 |
 |
Installing HID bulbs in your 04-05 Rhino factory housing:
Remove from stock housing (unplug). Remove stock bulbs by
pushing in tabs inside housing next to bulb, bulb will pop
out. Be careful don’t break tabs
Go |
 |
 |
Mounting: Mount light securely; making sure bracket is
square with vehicle. Tighten 17m bolt on the bottom of the
bracket to 50 ft/lbs. This bolt will not be loosened to
adjust beam. Wiring: All electronics are internal so there
is no need to mount external ballasts. Each light has a
simple 2 wire hook up. Red being + 12v and black being –
12v. Lights should be wired to a switch through a relay with
a maximum of 2 lights per relay for optimum durability and
performance. Each relay should be wired as follows;
Go |
